CONFIGURE THE PART NUMBER
Please select an option for each digit, then click the "Submit" button at the bottom.
NOTE: As you select your options, later options which are incompatible will be grayed out and cannot be selected.
To access these options please select "Reset All."
NOTE: As you select your options, later options which are incompatible will be grayed out and cannot be selected.
To access these options please select "Reset All."
| Selected Part Number: UPM-H_ _ _ -_ _ _ -_ _ _ _ _ |
| DIGIT | OPTIONS |
| SERIAL I/O (Digit 5): |
0: USB
1: RS485 9: Custom - Contact OTEK |
| GRADE (Digit 6): |
0: Industrial & Plastic
2: Industrial & Plastic NEMA 4X 9: Custom - Contact OTEK |
| # OF CHANNELS (Digit 7): |
1: ONE
2: TWO 9: Custom - Contact OTEK |
| INPUT SIGNAL (Digits 8&9): |
01: Volts A.C., All Channels, Signal Power
02: 5 Amps A.C., All Channels, Signal Power 03: Watts A.C., All Channels, Signal Power 04: Hertz A.C.V., All Channels, Signal Power 05: Mixed 2 Channel: VAC Ch. 1, AAC Ch. 2 ,Signal Power 06: Mixed 2 Channel: VAC Ch. 1, WAC Ch. 2, Signal Power 07: Mixed 2 Channel: VAC Ch. 1, Hz Ch. 2, Signal Power 08: Mixed 2 Channel: AAC Ch.1, WAC Ch. 2, Signal Power 09: Custom - Contact OTEK 16: 7-140 Volts A.C./D.C., All Channels, Signal Power 17: 10-50mA, All Channels=Input, Loop Power 18: 10-500mADC, All Channels=Input, Signal Power 20: 4-20mA F.S. (All Channels Same Input) 21: 100mV DC F.S. 22: 1VDC F.S 23: 10VDC F.S. 24: 100VDC F. S. 25: 10mADC F. S. 26: 100mADC F.S. 27: Watts DC (1Vx1A) F.S. 28: Watts DC (1Vx1V) F.S. 29: Custom - Contact OTEK 30: 0.1V RMS F. S. 31: 1V RMS F.S 32: 10V RMS F.S. 33: 150V RMS F.S. 34: 250 V RMS F.S. 35: 0.1A RMS F.S. 36: 1A RMS F.S. 37: 5A RMS F.S 38: W RMS (1Vx1VAC) F.S. 40: W RMS (120Vx5A AC) F. S. 41: Hertz (10KHz/5V Logic) F.S. 42: Hertz (120VAC/40-100 Hz) F.S 43: Hertz (240VAC/30-100 Hz) F.S. 44: Hertz (120VAC/500 Hz) F.S. 45: Strain-Gage (?300<4K Ohm) 47: RTD (PT100) 48: RTD (PT1000) 50: TC (Type J) 51: TC (Type K) 52: TC (Type T) 53: pH (0-14.00) 54: ORP (0-2000mVDC) 55: % RH (Specify Sensor) 56: Resistance (0-10K Ohm) 57: 10-50mA F.S. 58: None (Serial Input Remote Meter-1 Channel) 1A: Any Digit 15, TTL Input Level 1B: Any Digit 15, H.V. Input Level 1C: Any Digit 15, V-F (Option K) Input Level 60: 1V Ch.1, 1A Ch.2 (.2 Ohm) DC 61: 10V Ch.1, 1A, Ch.2 (.2 Ohm) DC 62: 100V Ch.1, 1A Ch.2 (.2 Ohm) DC 63: 100V Ch.1, 5A Ch.2 (0.02 Ohm) DC 64: 150V Ch.1, 5A Ch.2 (.04 Ohm) RMS 65: 250V Ch.1, 5A Ch.2 (.04 Ohm) RMS 66: 150V Ch.1, 100Hz Ch.2 (120 V Line) RMS 67: 250V Ch.1, 100 Hz Ch.2 (240V Line) RMS 68: None (Serial Input Remote Meter-2 Channel) 69: Custom - Contact OTEK 2A: Any Digit 15 TTL Input Level 2B: Any Digit 15 H.V. Input Level 2C: Any Digit 15 V-F (Option K) Input Level 79: Custom - Contact OTEK 89: Custom - Contact OTEK 00: 4-20mA, All Channels=Input, Loop Power |
| POWER INPUT (Digit 10): |
0: Powerless™ (No Power)
1: Non-Isolated USB 2: Isolated 5VDC 3: Isolated 7-32VDC 4: Isolated 90-265VAC 9: Custom - Contact OTEK |
| CONTROL OUTPUTS (Digit 11): |
1: CH. 1: O.C.T. (4)
2: CH. 1: Relays (4) 3: CH. 1 & 2: O.C.T. (8) 4: CH. 1 & 2: Relays (8) 9: Custom - Contact OTEK 0: None C: H.V. SPDT REED RELAY (4) D: H.V. SPDT REED RELAY (8) E: H.V. SPDT REED RELAY (12) F: H.V. SPDT REED RELAY (16) G: H.V. SPDT MOSFET (4) H: H.V. SPDT MOSFET (8) J: H.V. SPDT MOSFET (12) K: H.V. SPDT MOSFET (16) |
| ANALOG/POWER OUTPUT (Digit 12): |
0: None
1: CH. 1: 4-20mA Out 2: CH. 1: 30V Out 3: CH. 1 & 2: 4-20mA Out 4: CH. 1 & 2: 30V Out 9: Custom - Contact OTEK |
| SCALE PLATE (Digit 13): |
0: Standard
9: Custom - Contact OTEK |
| RANGE/CALIBRATION (Digit 14): |
0: Standard
9: Custom - Contact OTEK |
| COUNTER/FUNCTIONS (Digit 15): |
0: None (Use Digits 8 & 9)
1: Up/ Down Counter 2: Totalizer 3: Quadrature 4: Batch 5: Frequency 6: Period 7: RADS 8: REM 9: Custom A: Up/ Down Timer B: Time Interval C: Elapsed Time D: Range E: Julian Clock F: Rate G: Ratio H: Phase Angle L: Integration K: V-F (Voltage to Frequency) M: Pulse Width |
| OPTIONAL NOTES: |
Model UPM-H
Note:
1) If you select USB as the Power Input (Digit 10, Option 1), you must select USB as the Serial I/O (Digit 5, Option 0).
2) The number of Outputs (Digits 11 and 12) cannot exceed the number of Channels (Digit 7).
3) If you select Option 0 (None) on Digit 15, you cannot have options 1A-1C as your Input Signal on Digits 8 & 9.
1) If you select USB as the Power Input (Digit 10, Option 1), you must select USB as the Serial I/O (Digit 5, Option 0).
2) The number of Outputs (Digits 11 and 12) cannot exceed the number of Channels (Digit 7).
3) If you select Option 0 (None) on Digit 15, you cannot have options 1A-1C as your Input Signal on Digits 8 & 9.
